Any tips on installing an in-line fuel filter? (It's a Honda CTX200, if that matters.)

And anybody have recommendations for what to use to filter really dodgy petrol before it goes in your tank? (Something you pour it through...)

For filling the tank just use any bit of fine mesh material such as mosquito netting or muslin stuff; I did it many years ago by draping the bit of material into the tank, kind of wrapped loosely around the filler neck and then taking it out afterwards with any particles trapped in the fine material - then "backwash" the material to get it ready for next usage.

If you have a mossy net anyway it can do both jobs!!

Dave

__________________
Dave

I use a paper filter that's designed for lawn mowers, fairly universal.

My bike is not a CTX200 so I apologise if this is not relevant.

I just bought a standard 'paper' in-line filter from an internet parts shop. It's a small plastic rectangular cube and works well. Try to install the filter so that gravity fills the filter housing with petrol as it is possible to get an 'air lock' in the filter which can stop fuel flow. Mine isn't and it caused a few problems till I could get it to fill. Now the syphon effect keeps it full.
I just cut a piece out of my fuel line the slightly shorter than the length of the filter and fitted it. I fitted mine close to the fuel taps (my acerbis tank has two taps).
The first filters I got were car type ones and far too big, I kept having problems with the fuel flowing through them, so get the small ones designed for bikes. The clear plastic housing can sometimes become victim of 'vapour-lock' in very hot climates. This is (if you don't know) where the fuel vapourises due to the heat and can cause similar problems to an air lock or air bubble. I wrapped mine in sticky alu foil to reflect the heat away which comes from the sun/engine. I left a 'window' in the foil so I could see if the filter was full of fuel and if the paper element was getting dirty.
Don't know whether your bike has a fuel pump or not. Some filters are designed to be used with fuel pumps and require some pressure for the fuel to flow so I believe. Mine doesn't so I had to make sure I got filters that would work with the minimum amount of pressure in a gravity fed fuel line.

Hope this helps!

Matt

__________________
http://adventure-writing.blogspot.com

http://scotlandnepal.blogspot.com/

*Disclaimer* - I am not saying my bike is better than your bike. I am not saying my way is better than your way. I am not mocking your religion/politics/other belief system. When reading my post imagine me sitting behind a frothing pint of ale, smiling and offering you a bag of peanuts. This is the sentiment in which my post is made. Please accept it as such!

any offroad store should have a selection of in-line fuel filters, you just snip the fuel line where you want the filter and put it in, job done. a couple of clamps or clips are recommended though.
to fill, pull the whole line out of the carb and point it downward. open the fuel tap till fuel spills out the bottom then clamp the end(fold it over). flick the filter a few times to get any bubbles out then plumb the line back into the carb.

__________________
dave

Thanks for the tips, guys. Got a basic in-line to install and will figure out something to poor through if it gets really sketchy!

Make sure you put the filter the right way around, following the arrow on the filter usually. A friend of mine spent many hundreds of dollars sorting out an intermittent irregular running problem on his TransAlp only to find it was caused by the paper cone in the $3 filter having come unstuck and blocking the outlet (well, inlet really if it was the right way).

Regards

Nigel in NZ

__________________
The mouth of a perfectly contented man is filled with . -- 2200 BC Egyptian inscription

oh yes Nigel, forgot about that, well done. even the small square inline ones have an arrow on them

__________________
dave

Make sure the filter is not too close to the engine. Some of the fuel will heat up and vapourise inside the filter and create an air lock and it will take your three days of repeatedly stripping out and cleaning the carb before you realise why the bike is stalling the whole time.

__________________
If there's a will there's a way so I will anyway!
http://www.buyaikhaya.blogspot.com

I carry one of these Mr. Funnel it even takes out the water from the condesation in those 50 gallon drums, you know the kind you find scattered around the third world staffed by 11 year olds. It doesn't cost much is very small and light, and gives you peace of mind second to none, why only have an inline filter and take the chance of nuking your ride when you can carry one of these.

Nice! But how much room does the small one take up? At US$15 for the smallest, it's something worth considering.

Regards

Nigel in NZ

__________________
The mouth of a perfectly contented man is filled with . -- 2200 BC Egyptian inscription

A small Chamois leather is simple and effective

What about coffee paper filters? Easy to find, cheap and biodegradable! Never seen anyone using it though...

Hope im not to late to put my 2 cents in! I bought a tank filter fromhttp://www.procycle.us/bikepages/dr650.html cost $30 and sits in the top of your tank. you can pull it out, turn it inside out, get the crap out and put it back in. Its make of an ultra fine mesh, very similar to the filter material at the top of the petcock pipe in your fuel tank. Works great.

Since fuel injected bikes seem to be especially prone to problems with dirty fuel, I installed one of these SplitStream filters in the neck of fuel tank, so every fill up gets filtered.

So far so good, but I haven't traveled outside the USA with it yet. I'm going to Mexico in February, so I'll give you an update after the trip.

__________________
Giant Loop Moto